![setup iscsi vmware esxi 6.7 setup iscsi vmware esxi 6.7](http://vcloud-lab.com/files/resized/562001/1170;911;f74dc0fce0a4f564b345b5cbfaaf19fbe7a7145c.png)
- #Setup iscsi vmware esxi 6.7 how to#
- #Setup iscsi vmware esxi 6.7 drivers#
- #Setup iscsi vmware esxi 6.7 update#
So, I went ahead and dumped the list of VIBs using the secureBoot.py script, reformatted the list to a column and then proceeded to create a list of “esxcli software vib remove -n xxxxxxx” commands.
![setup iscsi vmware esxi 6.7 setup iscsi vmware esxi 6.7](http://docs.cloudstack.apache.org/en/4.15.2.0/_images/vmware-iscsi-datastore.png)
For example: net-tg3 or scsi-megaraid-sas.
#Setup iscsi vmware esxi 6.7 drivers#
However, what I did learn from Engineering is that vmklinux drivers usually (but not always) start with a prefix and a dash. There’s no API or metadata that I could use to provide a list. To differentiate between native and non-native drivers is somewhat difficult. These drivers are already on the road to being deprecated (and native has performance advantages) so it was best to clear them up while I’m in there.
![setup iscsi vmware esxi 6.7 setup iscsi vmware esxi 6.7](https://2.bp.blogspot.com/-02SMZ2Nagko/TmkaQielcRI/AAAAAAAAA2s/8_2CDqqdck0/s1600/5.png)
Meaning, they are drivers built using the vmkLinux API’s. In many cases these were drivers that weren’t “Native”. For example “ net-tg3” and “ ntg3” or “ net-bnx2i” and “ bnxnet” I noticed a lot of drivers that seemed to be duplicates of existing drivers. When It came up with no VIBs then I was confident that Secure Boot would work. As I removed VIBs I would always re-run this to ensure I caught everything. Using this command during this process became mandatory. Using the KB’s above as a starting point, I logged in to the host and ran the following command:Īll tardisks validated. This updated some of the VIBs but not nearly all of them. The first step I tried was installing 6.7 from an ISO over the existing installation of 6.7.
#Setup iscsi vmware esxi 6.7 update#
If you have updated using VUM or via an ISO update then you may find that your VIB’s have been updated with their signatures and you are good to go. If you updated using ESXCLI then you may encounter this issue. Hence, if the VIB is not updated in the update and carried forward as is, we can’t verify its signature. Why did I get this PSOD? This is because prior to ESXi 6.5, we did not save the required VIB metadata necessary for Secure Boot to work. I rebooted into the UEFI BIOS and turned off Secure Boot until I was sure it would work. Before I could continue, I needed to fix this. Also, some of these drivers are not “Native” ESXi drivers. Well, Secure Boot is working as designed! It has encountered a number of VIBs that don’t have their VIB signatures carried over via an update. When I went in to the UEFI BIOS and enabled Secure Boot I got this. If I was using Host Profiles then I’d be booting a clean copy of ESXi and would probably not be encountering these issues! PSOD! As you can see, this caused me some heartache. Older drivers that are replaced with newer drivers, older drivers from the server vendor that are now deprecated, etc. Like many of you, I tend to just update in place and this leads to the accumulation of “stuff” on my systems. But now it was time to update the bare metal hosts.
#Setup iscsi vmware esxi 6.7 how to#
This blog article is Part 1 of a two part series on how to configure your hosts to use SecureBoot and TPM 2.0.Īll my prior testing with 6.5 and during 6.7 beta was done with nested virtualization and fresh installations. But I had a few issues before I was able to get everything working. I had gotten my Dell R630’s updated with TPM 2.0 chips and was looking forward to booting with “attested” hosts. When 6.7 went “GA” or General Availability, I was excited to get it installed and running on my bare metal hosts in my lab here at VMware.